SL-030 Surface Resistance Tester Anti-static Tester SLD Static Tester New

Description

Develop Industrial
SL-030 Surface Resistance Tester Anti-static Tester SLD Static Tester New
Specifications:
1.SL030 Antistatic Surface Resistance Tester
2.can inspect anti-static products ability
3.measure the surface impedance
Description:
1.This small pocket detection table can measure the surface impedance, and measurement of ground resistance, wide range, from 103 ohm/ to 1012 ohm/, accuracy of + 1/2 range.
2.030 adopts ASTM standard D-257 parallel electrode sensor method, can simply, repeatedly measure all kinds of transmitting, electrostatic discharge, insulating surface.
Technical parameter:
Power:: 9V PP3 alkaline battery
Test voltage:: 9V
Temperature range:working temperature 5℃--49℃
Storage temperature:-15℃--60 ℃
Relative humidity: 0%--90% (not state of condensation)
Measuring degrees: in the order magnitudes of ten
Change point:1/2 Logarithmic degree (3.16* 10 n)
Transition point accuracy: + 1/2 degree
Accuracy: + 10 %
Repeatability: + 5%
Weight: 170g
Dimensions: 130 * 70 * 25 (mm)
HOW TO USE:
To measure the surface impedance, place the meter on the surface to be measured and hold down the red Test button. The continuously illuminated LED indicates the magnitude of the measured surface impedance.
103=1千Ohm green LED
104=10千Ohm green LED
105=100千Ohm green LED
106=1兆Ohm yellow LED
107=10兆Ohm yellow LED
108=100兆Ohm yellow LED
109=1000兆Ohm yellow LED
1010=10000兆Ohm yellow LED
1011=100000兆Ohm yellow LED
1012=1000000兆Ohm red LED
1012=insulation red LED
Measurement of resistance to earth:
1. Insert the Ground wire into the Ground socket, so as to insulate the detection electrode on the right side of the meter (on the same side with the socket). Clamp the alligator to your floor.
2. Place the meter on the surface to be measured, hold down the Test button, and the continuously glowing LED indicates the magnitude of the resistance value to the ground. The unit of measurement is ohms.
Calibration period SL-030 surface impedance meter calibration method:
* Calibrate the SL-030 surface impedance meter every 12 months
* Using a decade resistance box, connect the standard measurement resistor between two parallel electrodes of the SL-030 meter to verify that the displayed impedance value is correct.
Calibration procedure of surface impedance meter:
1, SL-030 surface resistance tester uses 1% ultra-thin film resistance and high-speed amplifier circuit, its calibration steps are based on the linear circuit technology of the product.
2. The conversion point of impedance value is 1/2 logarithm, that is, 3.16× 10N, and the linear value of the conversion point is ± 10% of the mean value perunit of each measurement gear.
3. Measuring instrument: Decade resistance box. The resistance of the test electrode resistance box should be 1×103 to 999×106 megohm or 109. CADGENERAATED techniques are used when the resistance value is greater than 109.
4, connect the resistance box of two electrodes to SV - 2080 on two parallel electrodes, dispatch resistance to 1 k, the table of 103 light-emitting diodes (leds) should be bright, other archives of calibration and so on, measure the impedance transformation point, press the switch and continuously adjust the impedance values of impedance bridge, and observation was made in a LED lights when normally on the impedance value (when the value for the transformation of impedance values).
Notice: According to international shipping requirements, it is forbidden to have powder, liquid, nor battery in package,In order to avoid delay of transportation, we will have to check and take out these items before packing.
Return Policy
Payment
Feedback
WARRANTY
Contact us
Dear friend, your happy is very important to me! We check all items before we send it out, to ensure every item sent to you is perfect.when you receive the item , if you find any question , please contact us .we very glad to solve all problem with you .if you Not satisfied with our item.you can sent the item back with 14 days , we can refund your payment , or exchange items from us .Accepted items return or exchange in brand new condition.Items must be return to us within 14 days after you receive.
We currently only accept payment through PayPal.
Payment must be made within 12 days after the auction/bid ends, or eBay will open Unpaid Item case automatically later.
We strive for positive Feedback on all transactions and nothing less than an overall Detail Seller Rating (DSR) of 5 STAR.If you are considering giving a neutral or negative Feedback or a low DSR. Do write to us and give us an opportunity to address your concerns firstly.We will leave the positive feedback when we got your positive feedback.
How to do the warranty: The warranty will be covered by natural faulty not including man-made damaged. If you receive a defective item or any item needs to be repaired under the warranty period, buyers have to report to us within 3 days and take a picture to show us the damage part and outside of package after received the item. We will try to help you solve the problem by e-mail. If still have problem, please kindly send back the defective item for our repair by freight prepaid. Returning postage is buyer's responsibility. If it is our quality's problem, we will repair it and send the repaired item to you for free of charge. If the damage is made by wrong operation, we will ask for maintenance cost.
Please contact us with any comments, questions or suggestions that you may have bysending ebay message, All the mail will be replied within 24 hours. Please ensure your mail box would not blocked / filtered our mails.we will be happy to assist you.
please feel free to contact us for WHOLESALES deal,we will surely give you a satisfatory price.
We would try our best to serve you with any question / problem. Please contact us first before leaving Negative / Neutral Feedback or open any cases.
We work 6 Days a week From 9:00am - 6:00pm Monday - Saturday CHINA Time.
Sales Policy
Your bid is a contract - Place a bid only if you're serious about buying the item. If you are the winning bidder, you will enter into a legally biding contract to purchase the item. If payment is not received within 7 days, item may be offered to the next highest bidder or relisted at the seller's sole discretion.
Return Policy
We offer 90 days(used) or 180 days(new) free warranty (except consumables).we stand behind every product we sell.If you're not pleased with your purchase, we'll be happy to make an exchange or refund the product price less S & H within 7 days of your purchase. For any exchange or refund, we need the original receipt or a record of the purchase in our system, and the product must be in its original condition, including the box, packaging, and all accessories.Shipping and handling charges are not refundable.
International Buyers
VAT (Value-Added Tax) is buyer's responsibility. However, we will try our best to minimize it.
About US
We are professional EBAY sales team and lots of ebay buyers very satisfied with our services.You can enjoy top-quality product and high-quality services from us, Trust me that you will have a pleasant shopping experience in here.
Payment & Shipping
Copyright 2018 Develop Industrial. All rights reserved.
On Mar-24-21 at 02:26:12 PDT, seller added the following information: